Baron Air & Fuel_Afflicion Air Cleaner H-D XL Models Manuel d'utilisateur télécharger pdf

Page: 1LA-2990-00 & LA-2990-00B

Affliction Air Cleaner '93-'06 Big Twin Engines w/stock CV Carb

'01-'12 EFI Softail Models '04-'12 EFI Dyna Glide Models '02-'07

FLT Models w/Delphi EFI

CAUTION: We strongly recommend that a qualified technician install this kit

if you do not completely understand the instructions prior to the install.

Revision: 1.8 - 06/29/2012

INCLUDED IN THE KIT:

(1) Affliction Insignia Plate

(1) Gasket

(3) 1/4-20 x 3/4" Alloy Flat Heads

(2) Custom 3/8-16 Breather Bolts

(2) Custom 1/2-13 Breather Bolts

(3) 1/4-20 x 1" Alloy Steel Set Screws

(1) 1/4-20 x 1/2" SS Socket Low Head

(1) Custom Filter

(3) Aluminum Standoffs

(1) Chrome or Black Main Backing Plate

(1) Chrome or Black Filter Cinch Plate

(2) Chrome or Black Main Body Standoffs

(2) Main Body Seal Plates

TOOLS REQUIRED:

Blue Loctite®

3/16" Allen Wrench

7/16" Socket and Open End Wrench

1/2" Socket or Driver

Needle Nose Pliers

T-27 Socket or Driver

5/16" Allen Wrench

Harley-Davidson® Service Manual

INSTRUCTIONS:

1. First you must remove your stock air cleaner assembly and backing plate via the instructions in your service

manual. The carburetor flange and threaded bosses into the cylinder heads should then be cleaned. Remove the

backing on the supplied gasket and apply to the back of the large chrome backing plate.

2. Mount the large backing plate to the cylinder heads via the supplied spacers and breather bolts. Spacers have

a lip that helps them seat flush in the backing plate. Be sure to use Loctite® when securing the bolts. For Evo

engines, use the larger 1/2-13 breather bolts. For twin cam engines, use the 3/8-16 breather bolts. Tighten

breather bolts lightly allowing minimal play in the backing plate for ease with the next step.

3. Install the three supplied standoffs w/studs through the backing plate and into the carburetor flange. Apply

Loctite® to the threaded studs on the standoffs and secure finger tight (tighten down as much as possible by

hand, they will be torqued in the next step). Secure the breather bolts to ~50in/lbs of torque at this time.

4. Next install the seal plates that fit into the backing plates, sealing off the air/oil channels from the breather

bolts. Place filter over seal plates, and install cinch plate with supplied black flat head bolts sealing the air filter

and seal plates to the backing plate. Be sure to apply Loctite® to the three flat head bolts. Tighten the bolts to

~50in/lbs of torque.

5. Lastly, place the Affliction plate into the cover and install over the air filter using the supplied socket low

head bolt and Loctite®. Tighten the bolt, clean off the cover and around the air cleaner assembly. Installation is

complete. Be sure to clean and re-oil your air filter on a regular basis. Also, be sure to re-torque bolts after

riding to ensure air cleaner assembly remains secure.

Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or

fitment may be required. LA Choppers bears no responsibility on installation costs associated with this product.

5221 Oceanus Drive Huntington Beach, CA 92649 (925)583-2499 - Ph. (714)901-0520 - Fax www.lachoppers.com [email protected]

FLT Models w/Delphi EFI 1

Résumé du contenu

Page 1 - FLT Models w/Delphi EFI

Page: 1LA-2990-00 & LA-2990-00BAffliction Air Cleaner '93-'06 Big Twin Engines w/stock CV Carb'01-'12 EFI Softail Models &apos

Commentaires sur ces manuels

Pas de commentaire

Baron Air & Fuel_Afflicion Air Cleaner H-D XL Models Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Baron Air & Fuel_Afflicion Air Cleaner H-D XL Models. Baron Air & Fuel_Afflicion Air Cleaner H-D XL Models BLACK User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Baron Air & Fuel_Afflicion Air Cleaner H-D XL Models