Baron Exhaust_BIG 'N NASTY PIPES Kawasaki Vulcan 20 Manuel d'utilisateur télécharger pdf

Page: 1BA-1020-03

BIG 'N NASTY MUFFLER SET - KAWASAKI VULCAN 2000

We recommend the use of the factory service manual and the reading of the

instructions fully before beginning the installation to avoid issues or setbacks.

Revision: 2.7 - 04/14/2010

Install Time: Under 1 hour

INCLUDED IN THE KIT:

(2) Big 'N Nasty Mufflers

TOOLS REQUIRED:

Assorted metric wrenches & sockets - 8, 10, 12mm Phillips Screwdriver

INSTRUCTIONS:

The installation of your new Big N Nasty Slip-On Mufflers is reasonably simple. For best results we

recommend you follow the instructions below to save time and effort.

Please read the instructions fully prior to installing the mufflers (It really does save time and effort). If you feel

you don't understand it, please call our technical support line or we suggest you have the product installed by a

competent technician.

DO NOT START THIS INSTALLATION WHILE THE ENGINE OR EXHAUST ARE HOT!

1. Unlock Right Side Cover and remove it from the bike.

2. Remove clamp bolt on the upper heat shield (heat shield not the exhaust mount), just behind and below the

rear passenger peg.

3. Loosen the heat shield clamps on upper muffler starting near the rear cylinder head. You have two mufflers

on this bike; an upper (rear cylinder) and a lower (front cylinder). It is NOT necessary to loosen the shield on

the upper pipe of the front cylinder.

4. Slide the top clamp up and the bottom one forward and detach the clamps from the shields then remove the

upper shield from the pipe.

5. Loosen muffler clamp that connects the muffler section from the head pipe using a 10mm wrench or socket if

you have access.

6. Remove upper muffler bracket bolts that face upwards behind the upper tube below the upper arm of the

swing arm behind the foot peg. Do not lose the metal inserts and rubber grommets that are attached above and

below the mount bracket, these must be reinstalled on the new mufflers).

7. Slide upper muffler off and back from the head pipe being careful to not damage the muffler joint gasket.

(CAUTION: Be careful in the removal of these fabric gaskets, they are necessary for a proper seal with the new

mufflers).

8. Repeat steps 2 thru 7 for lower muffler (NOTE: Only the lower portion of the heat shield needs to be

removed).

9. Slip muffler gaskets back onto the pipes these muffler gaskets have a chamfered edge and a flat sided edge,

Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or

fitment may be required. Barons bears no responsibility on installation costs associated with this product.

5221 Oceanus Drive Huntington Beach, CA 92649 (925)583-2499 - Ph. (714)901-0520 - Fax www.baronscustom.com [email protected]

1 2

Page: 1BA-1020-03 1
Page: 2BA-1020-03 2

Résumé du contenu

Page 1 - Page: 1BA-1020-03

Page: 1BA-1020-03BIG 'N NASTY MUFFLER SET - KAWASAKI VULCAN 2000We recommend the use of the factory service manual and the reading of theinstruct

Page 2 - Page: 2BA-1020-03

Page: 2BA-1020-03BIG 'N NASTY MUFFLER SET - KAWASAKI VULCAN 2000be sure to install with the chamfer edge facing the rear of the bike. Slide the t

Commentaires sur ces manuels

Pas de commentaire

Baron Exhaust_BIG 'N NASTY PIPES Kawasaki Vulcan 20 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Baron Exhaust_BIG 'N NASTY PIPES Kawasaki Vulcan 20. Baron Exhaust_BIG 'N NASTY PIPES Kawasaki Vulcan 2000 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Baron Exhaust_BIG 'N NASTY PIPES Kawasaki Vulcan 20