Baron Footrest & Controls_PASSENGER SPORT BOARD & Manuel d'utilisateur télécharger pdf

Page: 1BA-7020-00

PASSENGER SPORT BOARD & SHORTBOARD MOUNT

BRACKETS - Yamaha Road Star 1999 - 2010

READ INSTRUCTIONS PRIOR TO INSTALLING FLOORBOARDS. WE

RECOMMEND THE USE OF BLUE LOCTITE ON ALL THREADED

HARDWARE

Revision: 1.6 - 06/07/2010

Install Time: 15 Minutes

INCLUDED IN THE KIT:

(2) Floorboard Mount Brackets (BLACK)

(4) M8 x 45mm Chrome Hex Bolts

(2) 1/4"-20 x 1/2" Chrome Flathead Allen Screws

(2) 3/8"-16 x 1.0 Hex Cap Bolts

(2) 3/8" Lock Washers

(4) M8 Chrome Flat Washers

(1) 5/32" Long Allen Wrench

INSTRUCTIONS:

Your new floorboards come partially assembled for shipping. Please follow these simple assembly procedures

prior to mounting the floorboards to your motorcycle.

Assembly

Fasten the floorboard assembly to the S" shaped mounting bracket (Baron logo facing out) using the

supplied 14mm bolt and lock-washer. Do not tighten at this time. (Barons recommends the use of Blue

Loctite on this bolt).

Set fore-aft floorboard angle by installing the supplied Flathead Allen screw in the cam bracket at the

desired angle hole. Baron floorboards set to a 15-degree position (middle hole) has been found to be most

comfortable and user friendly. Tighten flathead screw. Adjust side tilt angle by moving floorboard stop

screw in or out to achieve desired angle.

Now fully tighten the large 14mm mount bolt. Floorboard is ready for installation. Installation

Remove the two bolts from the left and right stock passenger peg mounting brackets and remove the stock

peg assemblies from the bike.

Install your new Baron floorboards in the same location using the supplied mounting bolts. Insert the

mounting bolts (with washer) through the floorboard mounts and fasten then to the bikes frame. It is best

to use Blue Loctite when mounting.

Adjustment of floorboard angle after installation

Slightly loosen the 14mm bolt located on the backside of the mounting bracket the floorboard is attached

to.

Remove the small Allen screw located on visible side of the pivot/cam bracket. Once this screw is removed,

adjust the cam to the desired hole and insert and tighten the Allen screw.

Re-tighten the 14mm bolt. Repeat this process on both sides.

NOTE: It is important to use Blue Loctite on all threaded hardware on the floorboard mounts and

pivots/cam

Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or

fitment may be required. Barons bears no responsibility on installation costs associated with this product.

5221 Oceanus Drive Huntington Beach, CA 92649 (925)583-2499 - Ph. (714)901-0520 - Fax www.baronscustom.com [email protected]

Page: 1BA-7020-00 1

Résumé du contenu

Page 1 - Page: 1BA-7020-00

Page: 1BA-7020-00PASSENGER SPORT BOARD & SHORTBOARD MOUNTBRACKETS - Yamaha Road Star 1999 - 2010READ INSTRUCTIONS PRIOR TO INSTALLING FLOORBOARDS.

Commentaires sur ces manuels

Pas de commentaire

Baron Footrest & Controls_PASSENGER SPORT BOARD & Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Baron Footrest & Controls_PASSENGER SPORT BOARD &. Baron Footrest & Controls_PASSENGER SPORT BOARD & SHORTBOARD FLOORBOARD MOUNT BRACKETS Yamaha Road Star User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Baron Footrest & Controls_PASSENGER SPORT BOARD &