Baron Suspension & Lowering_REAR LOWERING KIT Suzuki Manuel d'utilisateur télécharger pdf

Page: 1BA-7580-00

Rear Lowering Kit

Suzuki C-90 VL1500LC

BA-7580-00

WARNING: This installation requires the lifting of the motorcycle. Serious

injury can result from an improperly secured motorcycle. Ensure that the

motorcycle is securely supported during this procedure.

Revision: 1.6 - 06/07/2010

INCLUDED IN THE KIT:

(2) Dog Bones

INSTRUCTIONS:

The use of this product will lower your motorcycle approximately one- to two-inches and reduces suspension travel.

The lowering of either front-end, back-end or both causes the motorcycles chassis, foot pegs/floorboards, exhaust

and other items bolted to any portion of the bike to now be closer to the ground. When turning at both low and high

speeds these items can come in contact with the ground sooner than expected. This contact, should it happen, can

result in possible loss of control or may cause damage to the item. We strongly CAUTION the rider of a motorcycle

that has any combination of our lowering products installed to be aware of the reduction in the maneuvering of

your bike or the damage that could be caused to any of the items referred to above. Baron Custom Accessories

accepts no liability for any damages stemming from the use of these products. We do not recommend a lowered

motorcycle be ridden with a passenger!

1. Decide how far you would like to lower your bike. Refer to the hole-index chart in these instructions to

determine the proper mounting location holes for the drop you want to achieve.

2. Secure motorcycle to bike lift and raise the motorcycle so the rear wheel is unweighted.

3. For easiest access to the linkage remove the tool kit holder from the left side of the bike.

4. Loosen and remove the two self-locking nuts and flat washers from connecting arm bolts from the left side

of the motorcycle.

5. Slide connecting arm bolts out (it may be necessary to push bushing back to the left side to allow bolt head

to drop below frame. Reinstall in the same manner). Replace stock connecting arms with your new Baron

connecting arms. The end with the single hole goes down and attaches to relay arm. The end with three

holes goes up and attaches to the frame. Use the hole that lowers the rear your chosen amount. Reinstall

bolts, washers and nuts. Torque the two connecting arm nuts to 35 foot-pounds (48 Nm). Remove

motorcycle from lift.

NOTE: We recommend that you set the shock spring preload to a higher setting, especially if the motorcycle

will be used for carrying a passenger or heavy loads.

Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or

fitment may be required. Barons bears no responsibility on installation costs associated with this product.

5221 Oceanus Drive Huntington Beach, CA 92649 (925)583-2499 - Ph. (714)901-0520 - Fax www.baronscustom.com [email protected]

Résumé du contenu

Page 1 - BA-7580-00

Page: 1BA-7580-00Rear Lowering KitSuzuki C-90 VL1500LCBA-7580-00WARNING: This installation requires the lifting of the motorcycle. Seriousinjury can r

Plus de documents pour Pour les motocyclettes Baron Suspension & Lowering_REAR LOWERING KIT Suzuki

Voir le document Baron Suspension & Lowering_REAR LOWERING KIT Suzuki Manuel d'utilisateur

Baron Suspension & Lowering_REAR LOWERING KIT Suzuki Manuel d'utilisateur (1 pages)

Commentaires sur ces manuels

Pas de commentaire

Baron Suspension & Lowering_REAR LOWERING KIT Suzuki Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Baron Suspension & Lowering_REAR LOWERING KIT Suzuki. Baron Suspension & Lowering_REAR LOWERING KIT Suzuki Boulevard C90_C90T & Suzuki Intruder LC 1500 User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Pour les motocyclettes Baron Suspension & Lowering_REAR LOWERING KIT Suzuki

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Baron Suspension & Lowering_REAR LOWERING KIT Suzuki